Join Our Tribe
Lucia - Constant Voltage
PLM: Operating Voltage for the different models
Can I use LoZ and 70V on same line?
D Series: Is D Series EN-54 certified?
What is the input sensitivity of the FP+/C series amplifiers
Lucia - Rack Mounting
What is Class TD technology?
Can I mix two different Input Signals (Dante and AES) into one amp channel?
What is Dante?
LUCIA: Can I disable auto power down?
What Sample Rate Are IPD Amplifiers?
How should I set the limiter?
CAFE - How does BEL effect operation and power output?
What do the crest factor values represent?
Can I use a locking IEC mains cable?
Is Dante compliant with Energy Efficient Ethernet (EEE)?
E Series: Can I disable auto power down?
Why is there latency (delay) through LUCIA?
Can I adjust the noise floor?
Can Nomad Link be converted to Fibre Optic for long distances?
LM 26/44: Is there a fail-safe bypass relay?
Is there an Amplifier Redundancy and Failover scheme?
Is the power stage inherently bridged as on E Series allowing asymmetrical loading?
LUCIA: Why is the standby/fault light flashing green?
Does the Tesira Analog version amps allow analog inputs to be transmitted onto the AVB network?
Noise Floor adjustment E Series amplifiers
Can FP+ series amplifiers be used in a fixed install?
LM 26/44: Lake Analyzer Bridge
Lucia GPIO cable length
How much can I skew the output power using RPM?
Will CAFÉ software work with older PLM models?
Can this be used without Lake Controller?
Why do I have no sound over AES?
QoS Configuration of Ethernet Switches
How do I configure ACL filtered VLANs for multicast traffic management?
How do Intercooler® Cooling System work?
Is there a Tesira variant?
Maximum size of NomadLink System
Recommended Network Topologies for Dante Networks
Systune Integration with Lake Controller
PLM: Calculating the necessary gain setting in controller
When should I use hard or soft setting on VPL Limiter?
What is the lowest impedance value that LUCIA can handle?
Does D Series Tesira have processing features similar to a Tesira Server?
What is the GPIO max voltage?
What DSP processing does the LUCIA have?
What class of amplifier is used on the IPD models?
The Benefits of Regulated Switch Mode Power Supply (R.SMPS™)
Lucia - an Induction Loop amplifier?
Is the fan noise audible?
PLM: R.SMPS explained
What is CAFÉ?
What can the GPIO in LUCIA be used for?
What is 'RPM' (Rational Power Management)
CAFE - what does “positions per rack” mean?
Can I create my own presets in Lake Controller?
Are there any presets avaliable?
What does Energy Star compliance mean?
Can C: Series be used as a touring amp?
D Series Matrix Integration
What are the protection features?
What limiter circuits are incorporated into LUCIA and how do they operate?
C Series: Technology Brief
Once I update Firmware, can I use units with old software?
Video: How to run Lake software on an Apple laptop
Video: How to configure a PLM amp with EAW Greybox files
How Do I Use Device Control?
How do Access Levels work?
D 20:4 - What Is The Bit Depth And Sample Rate Of My D 20:4?
What Is The Bit Depth And Sample Rate Of My D 10:4?
How do I perform a password reset?
What should I do if the Firmware update is interrupted?
How do I lock the front panel for security purposes?
What happens when the AES67 mode is active?
How do I store and recall Frame and System Pre-sets?
How do I unlock the software If I have forgotten my pass code?
Where are Module, System and Sub-System configuration files stored and recalled?
What is AES67 Standard?
Is my unit bridge mode compatible?
What is Direct Drive technology?
How do I recover my device if the Firmware fails during upload?
Can I have schematics for my Lab.Gruppen product?
Can I run audio through the USB?
How do I Enable Auto Power Down?
What Bit Depth And Sample Rate are used?
How do I set up the Level, Limiter and Channel Link settings on the IntelliDrive Controller?
How do I find and create Log files?
How does the enhanced bass profile work?
What are Super Modules on Lake Processing?
How many PDX3000 amplifiers can I daisy chain?
What is the username and password for Telnet?
Why won't you share schematics for legacy products?
What is Telnet?
How do I perform a factory reset?
What are the requirements for Tesira?
Is the Lab.Level compatible?
Is there a low pass filter?
How do I connect a mixer?
How are the power ratings measured?
Can I remove Auto Power Down?
Why is there an audio drop out when switching from dual redundancy?
What are the minimum requirements for use with a tablet computer?
What does the <65v error message mean?
How to downgrade firmware to a version below 2.78?
How do I run RJ45 Nomad link over mic line?
Does the Unit have a Power Switch?
What is the GPIO Configuration
Why don’t you publish the damping factor?
How to perform a firmware update
What is the Crossover Configuration
How do I enable AES67 on my Lab Gruppen amplifier?
How to Perform a Firmware Upgrade
What types of Digital Clock Conﬁguration are Available
What are the available crossover configurations
What is the recommended operating temperature?
How to Store and Recall Files and Presets
Is NomadLink Network Available
What are the Features on the Input and Output
Does it Work With Third Party Control
How does the Output Current Peak Limiter (CPL) Operates
What is the Sensitivity and Headroom Available
turn a c and cx on and off using nlb 60
Lab.gruppen / LAKE dual redundant network guide.
Ports in use guide
What Is the RS232 Control Protocol
Does Lucia have DSP Processing
How To Configure IP Adress On Lake Controlle
Alarm system relay with the E series GPI contacts
What remote volume controls are available for the CA/FA Series?
How do I test the fan on my IPD?
How to Manage and Recall Presets on my IPD Amp?
How do I configure the network on my IPD ampplifier?
How do I integrate the alarm system relay for E series?
What is the current consumption for the FP series?
Where can I find the PLM network configuration guide?
How do I connect a new amp?
What are the set-up procedures for Bi-amping?
C Series - Why is the NomadLink network a closed-loop topology?
C Series - What are the maximum cable lengths allowed when using the NomadLink network?
NLB 60E - How long can cable runs be on the Ethernet network to connect to a PC?
:ucia - Can I use two separate volume controls via the GPI?
C series - How can I be sure that no protection circuits or safety functions interfere with the output signal?
Lake Controller - How do I perform a Frame Replace in Lake Controller?
PLM – What is LoadEd?
lab2000c - What are the specs?
FP – What does the MLS Switch do?
IPD2400 - How do I unlock access to presets?